Factory Price For Thermoplastic Epoxy - Polyurethane adhesive glue – DESAY
Factory Price For Thermoplastic Epoxy - Polyurethane adhesive glue – DESAY Detail:
5. Usage:
(1) pretreatment: the surface of the adhesive is cleaned.
(2) sizing: use sawtooth scraper to apply the glue on the surface of the adhesive evenly, also can use mechanical rolling coating, can not use brush brush (glue viscosity is large), brushing amount of about 250g/m2, specific according to the actual situation control the amount of glue.
(3) composite: after the glue can be composite adhesive.
(4) post-treatment: because this glue is a foaming adhesive, when the adhesive layer is cured, the glue can be drilled into the micro hole of the adhesive, play the role of anchorage, increase the bonding strength, and must be compressed after curing.
Product parameters:
Product name polyurethane foaming adhesive
Brands have to match
Type of PU – 90
Viscosity (MPa ·s) 3000-4000
Capacity multiple specifications
PH 6-7
Appearance color is brown
Curing time 60 minutes
Curing 90%
Shelf life is 12 months
Polyurethane foam
Product parameters
| product name | Polyurethane adhesive | Brand name | desay |
| type | PU | Viscosity（MPA.S) | 6000-8000 |
| Specifications | 0.125L、0.5L、1.3KG、5KG、10KG、25KG | Curing time | 0.5-1h |
| Exterior color | brown | Shelf life | 12 months |
| Solid content | 65% |
Packaging specifications
Features
It has the characteristics of superior performance, convenient construction, foaming after curing, insolubility and insolubility, high and low temperature resistance.
Scope of application
Manufacture of fire-resistant doors, anti-theft doors, household doors, cold equipment, and various fire-resistant and thermal insulation materials (rock wool, ceramic wool, ultra-fine glass wool, polystyrene foam plastic, etc.) are also used for bonding. For metal to metal adhesion.
Instructions
1. Principle of curing: This adhesive is a one-component solvent-free adhesive, which is cured by moisture absorbed in the air and on the surface of the adherend.
2.Surface treatment of the adherend: remove the oil and dust on the surface of the adherend. Excessive oil stains can be cleaned with acetone or xylene. If there is no oil stain, it is not necessary to clean. Time, if necessary, spray a small amount of water mist on the rubber surface with a sprayer.
3.Glue coating: Use a zigzag scraper to evenly apply glue on the surface of the adherend. Mechanical glue can also be applied, but brushing is not required (grease viscosity is large), and the coating amount is about 150-250g / ㎡. The surface of the adherend can be slightly reduced, and the surface roughness can be slightly increased, that is, as long as the surfaces of the two adherends meet and can fully contact the glue, the less the coating amount, the better, because the more glue is applied, the more The moisture absorbed on the surface of the adherend is limited, which will affect the curing time. If the amount of glue applied is required, a small amount of water mist can be sprayed appropriately.
4.compound: can be glued
5.Post-treatment: Due to the foaming adhesive of this rubber, when the adhesive layer is cured, the glue can drill down the micropores of the adherend, which plays an anchoring role and increases the bonding strength. The material is compacted and can be loosened after curing (the pressure is about 0.5kg-1kg / cm2).
6.Tool cleaning can use ethyl acetate solvent.
Precautions
1、Use a serrated spatula for the scraper, such as a flat plate. However, if the glue is applied too hard, there will be no glue left on the coating surface. If the glue is applied too lightly, the glue will be too much waste. The zigzag scraper is just as hard as it is, and the glue left by the sawtooth is as much.
2、The two bonding surfaces to be compounded must be glued on one side.
storage method
This product should be stored in a cool and dark place during storage. Generally in indoor warehouses, the storage period is one year. After each use of glue, the barrel with excess glue should be sealed and stored, and the upper layer of glue liquid will solidify and crust due to moisture intrusion. If it is not used for a long time, it should be sealed with nitrogen.
Product detail pictures:
Related Product Guide:
abide by the contract", conforms on the market requirement, joins from the market competition by its good quality likewise as provides more comprehensive and superb support for customers to let them become large winner. The pursue of the company, is definitely the clients' pleasure for Factory Price For Thermoplastic Epoxy - Polyurethane adhesive glue – DESAY , The product will supply to all over the world, such as: Bolivia, Argentina, Germany, They are sturdy modeling and promoting effectively all over the world. Never ever disappearing major functions within a quick time, it's a have to in your case of fantastic good quality. Guided by the principle of Prudence, Efficiency, Union and Innovation. the corporation. ake an excellent efforts to expand its international trade, raise its organization. rofit and raise its export scale. We've been confident that we've been going to have a bright prospect and to be distributed all over the world in the years to come.
By Christina from Bangalore - 2017.03.08 14:45
The company can keep up with the changes in this industry market, product updates fast and the price is cheap, this is our second cooperation, it's good.
By Adam from Uganda - 2017.06.22 12:49
